2018
AL#135 p.4
Charles Rufino
▪ Here’s a close look at the process of setting a violin neck. No innovative tools or new miracle adhesives here; just good old-fashioned methodical, careful work with traditional toos and designs. From his workshop at the 2017 GAL Convention.
2009
AL#97 p.4 read this article
Joseph Curtin
▪ It turns out that virtually every aspect of the violin can be altered to make it more playable, more visually interesting, and perhaps better sounding. What a relief! There’s life in the old girl yet. Are players brave enough to get on board?
2002
AL#71 p.30 BRB6 p.392
Don Overstreet
▪ Everything about the violin must be just so, since there are few details that an experienced musician is going to overlook. The instruments can be extremely expensive and the work standards are very high. Overstreet is an old hand at the game, and here gives the straight info on getting it right.
2001
AL#65 p.10 BRB6 p.82
Paul Schuback
▪ Schuback learned violin making in a small shop in France during the ’60s. This segment of his 1995 convention workshop lecture covers completing the plates and fitting the neck, fingerboard, nut, and soundpost to the body. There’s lots of local French color, old tools, and old ways presented here, as well as a bit of how the violin has changed since the days of the first Italian masters. Part One appeared in AL#63. With 33 photos, a diagram, and a sequence chart for building a violin.
This article has been nominated as one of the Guild’s fifty best articles published before 2010.
1995
AL#44 p.20 BRB4 p.230
Guy Rabut
▪ Apparently not every violinist is determined to have a fiddle that looks 300 years old. Rabut has made some interesting attempts to update the violin without sacrificing the tone that everyone demands. Can’t wait until these babies start showing up in symphonic orchestras. With 21 photos.
This article has been nominated as one of the Guild’s best articles published before 2010.
1995
AL#42 p.63 BRB4 p.493
Bill Daniels
▪ A simple sander to thickness rib stock for violins and violas.
1994
AL#37 p.26 BRB3 p.352 read this article
Michael Darnton
▪ And you thought you knew all there was to know about making that fiddle play. Darnton continues his instruction from AL#35. This time he tunes and fits the bridge, strings, tailpiece, saddle, and end button. With 13 photos.
This article has been nominated as one of the Guild’s best articles published before 2010.
1993
AL#35 p.6 BRB3 p.352 read this article
Michael Darnton
▪ To the uninitiated, violin setup seems to have way too many steps for the small number of moveable parts involved. Taken one step at a time, the mystery falls away. Darnton explains the tools and procedures he uses to get the most out of a violin. This segment includes fitting pegs, correcting problems with the nut, making a fingerboard, and fitting a soundpost. Part Two is printed in AL#37. With 30 photos.
This article has been nominated as one of the Guild’s best articles published before 2010.
1992
AL#32 p.64 BRB3 p.446
Michael Darnton
▪ What should one expect from a purchased ebony fingerboard? Should a fiddle bridge lean back, and how far? Can you offer hints about using hide glue? Darnton’s wide experience rescues another page of readers.
1991
AL#28 p.56 BRB3 p.446
Michael Darnton
▪ Why are bridges always made of maple? Why do fiddles have points? How does one tune a fingerboard? Do epoxy or superglue have any accepted uses on the violin? Darnton furnishes answers.
1990
AL#23 p.22 BRB2 p.486
Michael Darnton
▪ Topics include sharpening a peg reamer, dealing with fingerboard tearout, tailpiece setup, pitching the neck, and staining the bridges.
1990
AL#22 p.32 BRB2 p.486
Michael Darnton
▪ Darnton suggests the most basic reading list for those wishing to make their first violin.
1990
AL#22 p.32 BRB2 p.489
Michael Darnton
▪ About the angle of a fiddle bridge.
1990
AL#23 p.22 BRB2 p.494
Michael Darnton
▪ A new bridge on an old fiddle is too darn white. Here’s a recipe for a stain to spray on it.
1987
AL#11 p.50 BRB1 p.502 read this article
George Manno
▪ The reviewer finds this video to be a wise investment, especially for one new to the craft.
1986
AL#7 p.54 BRB1 p.439
Alan Carruth
▪ Carruth describes a fixture he uses to hold a violin bridge while it is being tuned. It will save your fingers and help prevent cracking the bridge.
1986
AL#6 p.26
George Manno
▪ Manno describes his method of tuning an out-of-the-box violin bridge for maximum performance. A “personal expansion” upon previously published work by Al Carruth.